FacebookTwitterDiggStumbleuponGoogle BookmarksRedditTechnoratiLinkedin

ECCO [UPDATE #1 - Working collaborative documents]

Written by Robert Greenyer on .

An instant on/off ultrasonically fluidised dusty plasma New Fire reactor

Second technical interview

Coupling ultrasonics to an alumina reactor core

Reactor core layout

New fire individual reactor core cross-section and operation

SEM / EDX grouped into pdf for easy cross-referencing

Could it work like this?

Is the foil making process also making Silver?

 
Direct Paypal address is:
This email address is being protected from spambots. You need JavaScript enabled to view it.

Bank details here

Donations of any size can be made direct to Quantum Heat C.I.C.s (the organisation that runs the MFMP) bank account here, thus saving charges:

BANK: HSBC
Branch Address: 153 North Street Brighton, East Sussex, BN1 1SW
Account Name: Quantum Heat C.I.C
Sort Code: 40-14-03
Acc No.: 12631571
IBAN: GB48MIDL40140312631571
SWIFTBIC: MIDLGB22

Bitcoin: 1JesTRUXU8jHb1haa1MoF2NvrU8gt5msCr


UPDATE #1 - Working collaborative documents

We have a number of documents being drafted where we are developing the testing protocol and investigating which equipment to bring. We welcome your input below

Comments   

 
0 #20 Tim 2017-05-08 00:45
Just a quick calculation with available information (after 5 minutes to reach steady state):

LENR Reactor with COP of 8, should heat about 1.7 Liters of water form 28 C to 95 C (delta 67 C) in one minute.

Or 1.7 L/min water Output at 95 C (input temp 28 C) this would demonstrate a COP of 8, if power input is about 1000 Watts.

Does Suhas currently have a flow rate estimation?
Quote
 
 
0 #19 Tim Reese 2017-05-06 23:08
Just to clarify...ECCO

What is the total power input, ECCO reactor?
1100 watts?

Is there a flow meter at the water input?

What is the water volume of system and flow rate?

Is there a standard to verify the resistive heating of water?
Quote
 
 
0 #18 Robert Greenyer 2017-04-21 11:49
Nice find Eros, Think we will get one...

...ordered
Quote
 
 
0 #17 Robert Greenyer 2017-04-20 20:06
ECCO - Making nickel foil for reactor discharge electrodes

This article details the process to make the Nickel foil used in the ECCO reactor core that acts as an electrode and a breathable fuel barrier.

https://steemit.com/science/@mfmp/ecco-making-nickel-foil-for-free-energy-reactor-discharge-electrodes
Quote
 
 
0 #16 eros 2017-04-18 17:42
Cheaper RF meter only 0.1-8Ghz
https://www.amazon.com/Safe-Living-Technologies-ED88T-Electrosmog/dp/B01COXUUVY
Quote
 
 
0 #15 eros 2017-04-17 09:44
Thank you. Drop link here when foil document is ready
Quote
 
 
0 #14 Robert Greenyer 2017-04-14 22:29
@Eros

Will write document on foil production process tomorrow - bit delayed - hope to do it Sunday.
Quote
 
 
0 #13 eros 2017-04-14 18:27
Hello, transmutations sites/areas is it posible to get more magnification? In Me365 sem pictures smaller scale - bubles are visible. Near Au maybe lot of NAE's..?
Coloured elemental picture from transmutated foil side are nice to get too.. Give idea how much foil total have Au.
Back side have some Pb, Do Suhas use Pb anode?
Ni foil, how much stripping ultrasonic power (power input & probe head area?) How ultrasonic-hydr ogen-plasma is done for foil? Before or after stripping?
How thick Ni foil is, it is not mentioned in documents(??) If got deposition time from Suhas it is posible to calculate deposition current..
Quote
 
 
0 #12 Robert Greenyer 2017-04-05 14:41
@Eros

Already bought one and it is on its way. Need to check if it includes the necessary PT500 RTDs - if not, these may suffice.

https://www.amazon.de/Temperaturf%C3%BChler-Kabelf%C3%BChler-PT500-Silikon-2-Leiter/dp/B006TC07F6

In terms of complete simplicity and getting up and running in minutes, we have had a quote of £1015is + VAT for this - which includes certified matched RTDs (which are normally in the $250 range each) and we can capture data out - compare the flow sensed to bucket weights.

https://goo.gl/UVBRzp

https://goo.gl/4UfCI0

Flow rate is at the bottom end of the range and outside of quoted accuracy for the meter. Waiting on feedback from supplier.
Quote
 
 
0 #11 eros 2017-04-05 10:43
https://goo.gl/Hk02Kx

Just buy one and send directly to india, cost less than 50$ ;) Suhas have skills & fittings to assemble it.

Ultrasonic flow measuring may interfere reactor 1Mhz transducers?
Quote
 

Add comment


Here is your generous contributions so far towards our $500,000 target, thanks everyone! : $45,020   Please Donate
See the current state of our booked costs here