FacebookTwitterDiggStumbleuponGoogle BookmarksRedditTechnoratiLinkedin

The Cookbook is in the signal... [UPDATE#6 - Symphony of the New Fire]

Scritto da Robert Greenyer on .

The End of the Carbon Age is Nigh
Thankyou to all those that helped us

Prepare thoroughly (Ni + LiAlH4 + Li)

  1. Bake Ni
  2. Reduce Ni
  3. Hydrogenate Ni
  4. Mix: Ni + LiAlH4 + Li
  5. Bake and vac reactor, add Mix, vac warm, add H2, Vac
  6. Heat to above Mössbauer determined Ni Debye (say 135C), pressure regulated to approx 1bar abs.
  7. Hold, pressure regulated to approx 1bar abs.
  8. Heat slowly to as close to Ni Curie as comfortable (Say 340C), pressure regulated to approx 1bar abs.
  9. Hold, pressure regulated to approx 1bar abs.
  10. Slowly lower temp to above highest known Ni Debye (Say 220C), pressure regulated to approx 1bar abs.
  11. Hold, pressure regulated to approx 1bar abs.
  12. Go as fast as possible through Ni Curie
  13. Hold, pressure regulated to approx 0.5bar abs.
  14. Cycle through 500C internal, pressure regulated to approx 0.5bar abs.
  15. Hold, pressure regulated to approx 0.5bar abs.
  16. Raise internal temperature to over 1200, pressure regulated to approx 0.5bar abs.
  17. Drop to around 1000C and hold, pressure regulated to approx 0.5bar abs.
  18. Raise internal temperature to near boiling point of Lithium
Some of the above steps may in time be redundant.

1h Thermal > x/β- (0-100KeV) emissions thermalised in Lead > IR/THz (via blackbody) > 5h (SSM)
where '>' means 'leads to'

You will need to use this calculator

In order to fully appreciate the information you will receive, you will first need to deeply read and take on board the following post.

UPDATE#1-The signal...

Thankyou to Ecco, Webscience and Mark for the analysis.


A chart showing missed pulses (because there was too big a burst?). Spot the outlier?

The Plot shows the %age of pulses lost due to pulse overlap versus each Spectrum taken. The Absolute Error Bars are reflective of the Live/Real Time Resolution, given only in seconds.  In lieu of this, the Right Ordinate Scale (thin Olive Bars) shows the actual acquisition/accumulation time of each Spectrum, so that one may see that the longer a Spectrum is taken, the less Lost Pulse %age error there is. There is a tradeoff however, in the fact that shorter Spectrum Periods help further define/differentiate a sudden burst of pulses from the background condition.

This Spectrometer follows the general structure of a Scintillator/MCA.  More information on Pulse Overlap can be found at the following link, although the definitions of various terms need correction/improvement:


The following are useful online references concerning Dead Time or Pulse Overlap (in no particular order):


After the MASSIVE broad band 'turn on' pulse, the excess heat mode is between 0 and 100KeV.
The Scintillator does not see below 30KeV and 30-50KeV is attenuated.

Much more detailed photometric analysis is being conducted and will be published later today.

UPDATE#2 - The video...

The team watched this video all the way through for the first time AFTER designing basically an E-Cat following discovery of the emissions.
It turns out Rossi had already talked about the what is important to capture the excess heat on the 12 March, 2012 - and even the E-Cat LT runs at "1500ºC" internally

UPDATE#3 - Iceberg in the *GlowStick*

Photometric analysis of the signal by Bob Higgins


UPDATE#4 - The Brilliance of Prof. Sergio Focardi

Whilst it is without doubt Prof. Francesco Piantelli that first discovered the Ni + H system in 1989 as we describe here, it was the long collaboration with one Sergio Focardi that allowed the early blossoming of the understanding of this nascent technology.

Whilst the MFMP had the extreme privilege of a long audience with Piantelli, we were very aware there was another man in the room. Piantelli clearly deeply respected and, in an Italian way one might say loved Sergio - it was also clear that he was moved to tears when recounting his physical and mental degradation through his twilight years. 

He shared with us the following video from 29th April 1994 of Focardi talking about their work together, to demonstrate just what a formidable man he was - you don't need to understand what he is saying to see that he was a shining intellect and an engaging orator.

This paper they produced together https://goo.gl/tn1f7w supports our findings, but in pure Ni + H systems.

What we have shown in a Rossi analogue however, has not been shown by any other party to date, not even Rossi. Since it is data from nature - failing exceptional other explanations that no-one has been able to offer or demonstrate since announcement - it is likely that in time, following our exact procedure as clearly detailed, the same kind of signature will be seen by others. Moreover, when seen, scientist will know they have an active system and can iterate to one that has higher output, be that by modifications to fuel, thermal profile or to the structure and materials used in the reactor design or its enclosure.

More specifically, this work by Focardi/Piantelli et al. does not show any separation between high broad band transitory event prior to onset of 'excess heat' and lower band events during periods of and only in periods of 'excess heat'. The combination of which explains both Celani's hitherto unexplained experience in 2011 and the consistent claims of Rossi. Indeed, the suggestion is that heat and emissions may have been mutually exclusive in their work at times.

This is good historical supporting evidence that allows us to have more confidence in what we are seeing, but it is a very different experiment with neither Li or Al present and conducted at very different temperatures.

UPDATE#5 - Looking under the cats skin, with the help of X-Rays

This "bad hand waving" video, recorded by Bob Greenyer on the 22nd February, discusses the early analysis of the E-Cat that developed between 16-22nd February as a direct result of seeing two shapes of EM radiation emitted from the *GlowStick* 5.2 Experiment.

CORRECTION: When Bob says that Mathieu's associate had said the signal was typical of a beta release, he actually said Bremsstrahlung radiation.

Bremsstrahlung Radiation: https://goo.gl/32s0Iq
Attenuation Calculator: http://goo.gl/ciBtsR
Lead Weight to Volume Calculator: http://goo.gl/EH6asj
Volume Calculator: http://goo.gl/LvIHCw

UPDATE#6 - Symphony of the New Fire

The major part of "The Cookbook is in the Signal" announcement will be ultimately contained in the dynamic live document below. Context for the sense of validity of our findings in the *GlowStick* 5.2 will be released into the program sections. We hope you join us in this revelation process, analysing and understanding each step until you see the consistent whole.

Be as critical as you are able, with justified reasoning, where gaps are identified - let us know in the comments and your contribution will be made public and date-stamped. We will endeavour to fill them together - we lit the New Fire together, let's explain it together.

This is your chance to make history the Live Open Science way.

Add comment

Security code


0 #365 Valeria 2023-05-23 16:43

My blog post :: affordable search engine optimisation Packages uk: comison.com/.../...
0 #364 pinterest course 2021-08-23 05:02
Nice content. I hope you can check some things i also put
hard effort to make!
pinterest course: youtu.be/oWd9vBKExHA
0 #363 промокод вулкан 2021-04-07 03:37
Промокоды — отличный способ привлечения новых клиентов интернет-магази нами, повышения их лояльности, а также увеличения
продаж. Поэтому обычно промокод вулкан: vse-o-sochi.ruы можно найти в рассылках магазинов.
0 #362 промокод детский 2021-04-06 15:55
Промокоды – это один из маркетинговых инструментов, которые используют магазины для привлечения новых и удержания старых клиентов.
Мы помогаем нашим партнёрам
(магазинам) распространить информацию
о скидках. Если наш пользователь совершает покупку
с промокод детский: promokod4u.comом или по акции - мы получаем вознаграждение.
0 #361 www.bilger.lt 2020-11-16 08:58
Do you have any video of that? I'd want to
find out some additional information.
0 #360 wholesale jerseys 2020-01-15 02:07
Hey there! This is kind of off topic but I need some guidance from an established blog.

Is it very hard to set up your own blog? I'm not very techincal
but I can figure things out pretty fast. I'm thinking about setting
up my own but I'm not sure where to start. Do you have any points or suggestions?

0 #359 GrettaBig 2019-09-20 08:22
Hi. I have checked your quantumheat.org
and i see you've got some duplicate content so probably it is the reason that you
don't rank high in google. But you can fix this issue fast.
There is a tool that creates content like human, just search in google:
miftolo's tools
0 #358 france 2019-07-28 17:53
I am not sure the place you're getting your information, however good
topic. I must spend some time learning more or figuring out more.
Thanks for fantastic information I used to be on the lookout for this info for
my mission.
0 #357 pb 2018-12-02 21:31
If you can it, hire a web-designer location a site together you.
I want being your possibilities for blogging, furthermore the reasons you
visit blogs.
0 #356 EffieJuicy 2018-10-14 23:45
Hello. I see that you don't update your site too often.
I know that writing content is boring and time consuming.
But did you know that there is a tool that allows you to create new articles using
existing content (from article directories or other pages from your niche)?
And it does it very well. The new posts are high quality and
pass the copyscape test. Search in google
and try: miftolo's tools
0 #355 nắp hố ga gang 2018-10-03 09:48
WOW just what I was searching for. Came here by searching
for Fleischmann
0 #354 ntc33 login 2018-10-01 13:53
Stick with just one to 2 font types so men and women will not be confused with your font selection. Them have built an empire
in the mlm field by being the pay a visit
to guys in SEO.
0 #353 rollex11 download 2018-09-26 21:25
Greetings from Ohio! I'm bored to tears at work so I decided to browse your website on my iphone during lunch
break. I love the knowledge you provide here and can't wait to take a look when I get home.

I'm shocked at how quick your blog loaded on my phone .. I'm
not even using WIFI, just 3G .. Anyhow, good blog!
0 #352 live22 2018-09-22 14:03
Really feel nice a good content of blood potassium. The spacing of the text lines and paragraphs could
make website content more readable. It took a while and effort but he soon started making
some decent dollars spent.
0 #351 MaynardBold 2018-05-25 12:59
I have checked your site and i have found some duplicate content,
that's why you don't rank high in google, but there is a tool that can help you to create 100% unique articles, search for; SSundee advices unlimited content for
your blog
0 #350 download fee 2018-02-25 06:07
Some genuinely rattling work on behalf of the owner of this internet site,
utterly outstanding content.
0 #349 jeff morriss 2016-05-06 06:39
For some reason my two precious posts were truncated. I'll try again.

Using external H2 source.

Based on the comments on this thread, it appears that LiAlH4 serves only as a source of H2. If that is true, then an external H2 source, such as a hydrogen generator, should suffice. Additionally, an external H2 source plus a vacuum pump permit precise control of H2 pressure up to 3 atm, which is the limit for the quartz cell.

The next question then, is the mixing and pre-treatment of the Ni and Li. In the last run I used 1g AH50 Ni + 0.1g passivated Li powder, mixed by shaking in a small bottle and then loaded into a 316SS capsule which was plugged on both ends with quartz wool to keep the powder in place. The capsule fits into an alumina tube wound with Kanthal wire in a quartz cell that can be pressurized or evacuated.

Pre-treatment consisted of heating the loaded cell to 250C while applying a vacuum to remove volatiles and to melt the Li, and was continued until a pressure of
0 #348 jeff morriss 2016-05-04 06:30
Continuation from last note...

until a pressure of
+1 #347 jeff morriss 2016-05-04 06:21
Using external H2 source.

Based on the comments on this thread, it appears that LiAlH4 serves only as a source of H2. If that is true, then an external H2 source, such as a hydrogen generator, should suffice. Additionally, an external H2 source plus a vacuum pump permit precise control of H2 pressure, as long as pressure is less than approx. 3 atm, which is the limit for the quartz cell.

The next question then, is the mixing and pre-treatment of the Ni and Li. In the last run I used 1g AH50 Ni + 0.1g passivated Li powder, mixed by shaking in a small bottle and then loaded into a non-sealed 316SS capsule. The capsule fits into an alumina tube wound with Kanthal wire in a quartz cell that can be pressurized or evacuated.

Pre-treatment consisted of heating to 250C while applying a vacuum to remove volatiles and melt the Li, and it was continued until
+1 #346 Donor#356 2016-05-02 17:13
@Robert Greenyer Please refer to my comments inserted amonst your original post after CAPS...

I am of the following opinion now. LiAlH4, Ni and free Li should not be mixed together in the reactor. In my opinion LiAlH4 serves only as a Hydrogen source first to Hydrogenate the Nickel before the Li Melts, then to make the Li on the surface of the Ni LiH. YES! limit how much H2 is in the Ni when you get initial ignition. Add more H2 after it's burning nicely...

The reversible reaction 2 LiH + 2 Al → 2 LiAl + H2 (R3) Allows the release and capture of H2 at will. YES!

The primary reaction is pure Piantelli Ni+H - the secondary reaction is 1H + 7Li > 2 X 4He. CORRECT, but Li is not essential, but it does work well in terms of clean exothermic production of alphas..

Our experiments so far have had all three reactants mixed together - and in this instance, as I calculated last year - the Al can play a role but it is in the way 27Al is a much bigger target than 7Li and in time it would destroy the (R3) reaction - that which enables the control of H2 in the cell since the Al would be transmuted and loose its function and the products are in the way. I AGREE.

The big yield is from 1H + 7Li > 2 X 4He, so you want nothing in its way. We, and other replicators may have seen low excess heat due to mixing everything together. YES.

I then had the inspiration that we might have mixed in a specific order in GS 5.2 - so I asked which order the powder was mixed in GS 5.2. Alan seems to recall the free lithium was added first - this is as I suspected and would be not ideal - but advantageous as per the above hypothesis. So, the suggestion is to, as a half way house, mix and pestle mortar the free lithium / Ni together before adding the LiAlH4 - or add mixed & ground Ni+Li to the cell first and drop the LiAlH4 in afterwards. First clean Ni & Li surfaces with H2 then diffuse Li throughout all the Ni pores. Then adjust H2 pressure ready for take off and go up through 700C chirping the power as you go up, or maybe bringing up a 13Cs or 90Sr source to get ignition and the big initial tell-tail pulse on The GM meter. ..

This is consistent with my calculations based on Piantelli theory, Rossi's 2012 interview with Ruby Carat and his diffuse LI and the claimed critical reversible reaction. It is also consistent with the implications of Ikegami, Unified Gravity Corporation and on the electron screening of molten LiH. TAKE your word for that

By having LiAlH4 in a different heated part of the reactor, it allows control of 2 LiH + 2 Al → 2 LiAl + H2 (R3) which means you can seal it up and control the H2 Pressure. YES!!

by varying the temperature of the Ni+LiH zone (above LiH breakdown) and LiH Al zone temperature you can control the ratio of H in LiH to enable molten LiH / Li on the Nickel at far lower temperature Li H liquid plasma. REACTION won't start until LiH is above 689C I think.

Here is your generous contributions so far towards our $500,000 target, thanks everyone! : $45,020   Please Donate
See the current state of our booked costs here